We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
Hello, I am making my first custom board based on nRF52832. I have used a custom antena design (due to PCB layout I did not use reference design). That was the very first...
Hi everyone,
We need your help with a condition that we encountered in our prototype of a nRF52840 that use a ceramic antenna. Our current design is poor and we will have...
Hello,
We have the following problem with a custom board based on the nRF52832 and the SKY66112-11 PA LNA, running as a mesh node.
The SDKs used are nrf5_SDK_for_Mesh_v3...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
My queries are:
1) In code I just changed...
Hello,
I have queries on Sniffer functionality.
1) Using nRF52840 USB dongle whether we can sniff BLE 5.0 packets.
2) Using nRF52840 development kit whether can I...
Here's is my device profile:
Running on SDK 15.2.0
FreeRTOS
Custom board, based on NRF52840
Powered by a 3.5Ah battery
Using CLI utility
Using the following...
Hello, we are developing a BLE application using SDK 5.2 and softdevice 6.2.1 (we are aware this is old, but we still have to support it).
We actually use Keil IDE 5.10...
Hello. I'm reviving an old project (nrf51 and 12.3.0 SKD with sd130 2.0.1). Unfortunately bootloader is not working properly. It worked just fine at the beginning of the year...
Hello:
GPS and LTE can't work at the sametime currenty with 1.0.0 modem firmware.
You know that EMC test need GPS and LTE work at the same time.
Will GPS and LTE work...
Hello, I would like to utilize UART and NUS to both send and receive data using the ble_app_uart example as a starting point. I have tried connecting to the nRF52 DK with...
