Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
I have a project that requires the use of the SAADC module for temperature measurement from an NTC Thermistor.
However, I will also like to use the CapSense touch...
Hi,
With reference to https://devzone.nordicsemi.com/f/nordic-q-a/33890/get-x-y-z-values-from-lis3dh-using-nrf52-development-board this thread. I am trying to get data from...
Hello,
My application is really close to the example named BLE relay example in the DK. We could start from this example and adapt it to our needs. The problem is that this...
I have the Adafruit Sniffer which is based on the nRF51822 Bluefruit LE Friend, which contains the Raytac MDBT40 . After searching and finding the CP2104 drivers, I can speak...
I have been reading the forum and there seems to be differing advice to use Timers or RTC, since TIMER0 is used by the soft device, so it could cause issues since the SAADC...
Hi All:
i have a trouble, i need Coexistence mesh sdk 2.0.0 provisioner and nrf SDK 15 template. but mesh not work when nrf SDK 15 run advertising_start(erase_bonds);
...
I'm working with nrf24l01 module and use it in BLE beacon mode.
My main question is how can I decrease the visibility range to 10 - 20 santimeters?
(by some schematic...
Hi Support team,
My search for nrf8001 port to Arm-m3 landed me on a thread , where the support personnel has provided a link for a port to lpc1769 in the last comment....
Hi,
I would like to add sensor data in mesh network to be able to send data in certain intervals. How is it possible when I create a sensor model for mesh client and server...
Hello. I have a nRF52832 DK and I'm trying to modify the SPI example code found here:
/nRF5_SDK_15.0.0/nRF5_SDK_15.0.0_a53641a/examples/peripheral/spi
I'm using the nRF52832...
Hello Guys,
I have brought this nrf52840 to try BLE mesh. I tried connecting it to the PC and it was working fine, later I tried dumping the file into the board through...
Hey Nordic and co-nordic developpers,
Just to show some capabilities here at work I want to compile and run the mesh demo on the 10 Thingy52's we have here. I am currently...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
