Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Here i have made an UART0_IRQHandler routine. When i try to send some 50 bytes data through UART using PC tool here its receiving bytes, but it only receives 1st 6 bytes which...
Hi Everyone,
I'm working on adding DFU on my project and here is my setup:
Softdevice = 7.1.0
SDK = 6.1.0
DFU Bootloader = Keil compiled from SDK 6.1.0
MCP...
I'm having a bit of confusion understanding how the nRF51 Series Compatibility Matrix works.
I have a QFACA10 development board running my software perfectly, but when...
The nRF51822 Bluetooth Smart Beacon Kit User Guide (nRF51822-BK-UG) mentions an iOS project contained in the zip file nRFBeacons_iOS.zip. Where is this file? I cannot find...
Hello all,
I'm trying to save the service context with the Device Manager on the Central side. But I don't understand the implementation on how to do this. But no information...
I'm trying to adapt the BLE_BAS_C library to perform discovery and read/write operations for a custom service. However, when I change the UUID that I register with ble_db_discovery_evt_register...
i used this function to send data to my ble device ble_nus_string_send.this function sends ASCII values. and when i pass this function hex values it converts them into ascii...
Hello,
I was using wiringPiSPI() to connect via SPI and so i was using wiringPiISR function to create an interupt handler that will do callback to the user suplied function...
I'm compiling my project successfully in Eclipse, but trying to build it from the command line (cygwin) fails near the end with this error (make, make all, make nrf51422_xxac_s110...
I want to restart the radio portion of the softdevice - all of BLE essentially - to update the connection parameters and device name mostly. Is it necessary to re-initialize...
Hello Everyone
I have designed the schematics for my prototype but i have a question for impedance matching can anyone verify my technical doubt
I had put a 2.45GHz...
We are using nrf51822 for products of our company. We use mbed + nRF51822 driver + BLE_API for the BLE peripheral devices. The softdevice is s130 ver 1.0.0.
I create an...
Can the nRF51X22 be paired with an iPhone to communicate (both ways) using regular BLE and emit a beacon signal at the same time? In fact, I'm looking to change the beacon...
So I suspect there is a very simple answer to this, but a couple days of much reading and searching haven't led me to a very clear answer.
My setup: Galaxy S3 (Android...
I'm trying to move data over the uart characteristic. I followed the guidelines here devzone.nordicsemi.com/.../
In the main loop I am calling sd_ble_gatts_hvx until it...
