I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm using nRF Connect SDK v2.1.2 with Visual Studio Code and a nrf52840DK.
I have implemented this app (OpenThread CoProcessor NCP from Zephyr) and it is working correctly...
Hello again!
I have configured and initialised the Thread API from the Thread/Zigbee client publisher example, and receive no errors or warnings when attempting to send...
Hi,
Is there a possibility to change the COM port number of the nRF52840 USB dongle manually?
I already looked in the device manager under the port tab, but couldn't...
Hi all, I have a prototype device app I'm going to "deploy" in a remote location with an nrf52840 dongle. Initially ble via special shell commands added to nrf/samples/bluetooth...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
Hi,
General information:
nRF52840 SoC
Our own PCB’s with inverted F-antenna
nRF Connect SDK v1.8.0
We are in the middle of approval testing our product. We have...
Dear all,
My application is build on nrf52, nrf connect SDK v2.0.0.
For energy saving purpose, I put the nrf52 into sleep mode, using these code
And wake up via GPIOs...
Hi,
I need to transmit and recieve data over the 2.4GHz radio. I have customized packets to be sent and received over the radio. But I dont want to use ESB or Gazell protocols...
Hello there,
I want to use the nrf52-DK with pc_ble_driver_py. According to the 52832 compatibility matix ( link ) , Revision 3 of the soc needs S132SD v6.1.1 at least....
Hello,
We have developped a product with the nRF52832. Basically, it is a power sensor that uses both BLE (advertising) and ANT+ to send data regularly to a display (third...
Hello, I have a question about the scan request event.
I checked the logs of BLE_GAP_EVT_SCAN_REQ_REPORT. If this event is received, does Softdevice recognize the packet...
What a pity ncs ota not support single bank, but old nrf sdk support.
I know mcuboot not support transfer image over bluetooth, i want to know if there are any other way...
NRF SDK 1.9.1
Modem Firmware 1.3.1
I currently have a production device out in the field that is connecting to a specific cell tower and has the ability to then connect...
hi
I want to use two i2c
But in devicetree add &i2c0 and &i2c1
but it shows undefined reference to `__device_dts_ord_131' and static assertion failed: "/soc/i2c@40004000...
