I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
On a custom board we are using an RTC chip to generate the 32khz clock.
I have verified that the hardware register is set to external, bypass, and the src is xtal. The clock...
when i got a nRF5340 DK,
firstly,i use the vscode to open sdk and build ,
secondly,start to run the ncs2.1.2 sample (path:v2.1.2\nrf\samples\bluetooth\peripheral_uart...
I wan't enable approtect by add this line in main.c:
const uint32_t approtect_set __attribute__((used,at(0x10001208))) = 0xFFFFFF00;
but when i compiled at IAR,its show...
Hi, I'm setting up my environment on a new laptop. The project I'm working on requires tflite-micro and before I found that I needed to add tflite-micro to the 'name-allow...
Hai Team,
I am working on NRF52840 based on the BLE Connection handle
Here I am using the ble_app_multilink_central example of SDK
case BLE_GAP_EVT_ADV_REPORT: { uint32_t...
Hello,
I'm following this tutorial to learn how to create a Matter application from template. I did all steps and wanted to build the application. However, the build failed...
Hello,
I'm using the nrf52-quadcopter example from NordicPlayground. After successfully building the project and connecting the MPU6050 , I got a hang during sensor initialization...
Hello,
I had bought 3 sets of Audio DK and had managed to brought up in BIS and CIS mode using the default sample project, however the output is mono output. Can I checked...
I've started to get this error when trying to do a DFU update on nRF Toolbox (v5.0.8): "Can not create Firmware".
The same firmware file worked before on the same device...
Hi. I'm using nrf5340. I confirm internal clock(LFRC RC osc) exist,I want to remove external 32.768kHz X-tal. If yes, how can I turn on LFCLK RC oscillator in my source code...
Hi,
I was successfully able to flash the peripheral_uart code to the dongle and then connect to the Nordic APP.
But it does not connect with the UART when in BLE mode...
I am working on nrf52810. I raised the RAM size in the linker file, which is larger than the real physical RAM capacity, for the testing purposes. I anticipate a hard fault...
Hi:
I use mqtt_ Sample routine: MQTT is connected to the server, and I shut down the server. At this time, the 9160 status has not been updated, but is still connected....
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
We plan to use the 52840 to make a module with an external flash, if we apply the QSPI peripheral, must we use the P0.23,P1.00,P0.21,P0.25,P0.19 pins recommended in the specification...
