I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi there,
Yet again we are running into very basic issues with the nordic tools and software, and this is adding up to cost us massive amounts of time.
Within nrf connect...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
Hello
SDK starts adverting when reset. I want to start adverting at the push of a button.
SDK version : 17.0.0
SWDevide : s112
When the button is pressed as above...
Hi all
I have an issue regarding central- peripheral connection.( using nRF52832)
In the past I developed a peripheral device using SDK 11.
In order to manufacture it...
Hello, I am doing a bachelor thesis using the nRF52 Development Kit to control a (RC ) car, and I am 3D-printing holders for extra peripherals. During the 3D-modeling and...
When I run nrfjprog --pinreset it says "Applying pin reset" but it has no effect on the connected nRF52832, it just continues running. Other nrfjprog operations like reading...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hello,
I am trying to get reliable log output using the Nordic Connect SDK (NCS) over RTT. When I use Minimal mode, the following config:
CONFIG_LOG_MODE_MINIMAL=y CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
Hello! I use EK42423-03 and 52833-DK
Previous case
I understand plugging in the SWF connector, Will disconnecting from the PCB antenna and routing the signal to the cable...
