I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hello, I'm trying to flash custom developed beacon based on nRF52811 and everytime i try to flash i'm always greeted with an error "Failed to write memory" i have attached...
Hello,
I am trying to merge mqtt_simple and gps together. Each of them is working well on Thingy:91.
1. I am using lte_lc to configure the modem and enable PSM and eDRX...
Hello All,
Right now I am working with: https://www.digikey.ca/en/products/detail/circuit-dojo/PASSY-NRF9160-FEATHER/13668137 which I think is practically the same as https...
As everyone knows, the supply of semiconductors is pretty bad now. Normal suppliers such as Digikiey have zero stock. Recently we have had to purchase from less known distributors...
Hi everybody! My application is based on SDK 17.02. I try to communicate with an spi device using spim driver and the code is basically based on the nrfx-spim example.
After...
I am using latest version, nrf connect sdk v1.4.99-dev1
when activating bt_enable, application gets stuck
applications without BLE works well
I am working with...
Hi I'm Frank.
I'm testing Serial DFU via UART using TWO nRF52840 DKs(DFU master and DFU slave DK).
I want to update firmware of slave DK through the master DK.
I was...
dear all:
I use the latest sdk17 to test the ANCs sample on the 52840 DK。 The address of the example is: SDK_Path\examples\ble_peripheral\ble_app_ancs_c。after...
I have a example application (gatt central) that works fine on the nRF52DK dev board. I'm able to change the advertisement name, connect to it with my phone, and see the characteristic...
Hello everyone,
Yesterday I found a strange behavior with the NRF9160 GPS on NCS v1.5.1:
When configuring the GPS to run in Single Fix mode, running on MFW v1.2.3, I noticed...
*** edit: Problem solved. My project file had build config set to "release", I had to change it over to "Debug".
Kindly close the case ***
I have an i2c program running...
Hello,
I would like to ask for guidance, as I am at the very start of a human interface device (HID) controller development, considering BLE nRF52840.
The use case I would...
Hello!
I am trying to get basic communication between two nRF24L01+ modules to work on Teensy 4.0's, but I am having trouble transmitting and receiving.
Here is the wiring...
Hello, DK:nrf52810
sdk:17.0.2
In my project i have to advertise accelerometer and gyro value through beacon so i have done with using https://devzone.nordicsemi.com/f...
Hi Nordic Mesh experts,
I'm testing for the BLE mesh using light_switch example based on nrf5 sdk for mesh and nRF Mesh APP.
From the printed info on the APP during connection...
