Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi i m evaluating the nrf5340 and i get this message when i try to download the code to NET cpu and it's a bit impossible to attach the debugger
CTRL-AP indicates that the...
Hi,
My nRF52840 DK has suddenly stopped working. I have tried different USB cables but it's not turning ON when I connect the cable to the J 2 USB connector.
Observation...
Hello
In our application we're using the download client. Here are the cipher suites the modem supports in hardware: https://www.nordicsemi.com/Products/Low-power-cellular...
nRF52840, SD140, SDK 17.0.2
We're using UARTE to communicate with a peer MCU. We're using hardware flow control (CTS and RTS are enabled) and the baudrate is 115200. The...
Hello,
I'm using two nRF5340 MCUs with BLE5.2 audio in an application. I had a couple questions I hoped the Devzone could help answer.
1. On one of the MCUs, I was originally...
sorry for the perhaps stupid question - but despite several hours of intensive searching, I am not getting any further with the start -up of my new and beautiful Thingy91...
I do not understand how to compose these settings.
Using ncs v1.5.0 GPS sample with SUPL enabled.
This works OK on nrf9160-DK using the supplied settings
#define AT_MAGPIO...
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/61935/bootloader-flashing-error---nordic-nrf52840-usb-dongle I get the following error:
DFU failed: Error message...
Hi,
I’m trying to measure the current on NRF52840, SDK 17.0.2.
I have modified the HeartRate Measurement example’s advertising parameters as PLper my requirement.
...
Hi,
I am trying Zephyr for 52840 dongle. I am able to west build, but could not west flash.
While I do west flash, I get
-- west flash: rebuilding ninja: no work...
I bet you get sick of this, but I've looked at the other solutions and followed any advice, but no joy.
I am trying to use a Makerdiary nRF82540-MDK usb dongle to evaluate...
Dears,
When Reset pin(0.18) is used for QSPI (GPIO macro is not defined as RESET), after initialization ,Jlink is disconnect.
Would you please suggest it? Thanks.
I am using a nRF52840 dongle and want to filter ADC raw data. I have downloaded the CMSIS 5 DSP package.
And tried to include a copy of an example (arm_fft_bin_example_f32...
I found that AGPS can get location information via mobile network. With this feature "GPS" can work indoor.
1. Thingy91 also uses AGPS, but when I ran prebuilt hex asset...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
