I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello There,
I have problems with the installation of the nRF9160. Started the installation earlier and nRF9160 was detected in nRF Connect/Programmer and I could see memory...
Hi, For my application I was using ESB without softdevice and just recently I wanted to add dfu so I had to add softdevice as well. After adding softdevice I found out that...
I want to convert APP_TIMER_TICKS ms to us.
So i'm using this function.
And, the value of APP_TIMER_CONFIG_RTC_FREQUENCY is
Also this is main code.
And, I...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hello,
Is there a modified radio test firmware available? I am hoping for something that can be connected to via BLE, command it to turn on a tone, and then reboot the processor...
Hello,
I'm trying to send and receive data between the nRF52832 chip and a phone by following this tutorial:
https://github.com/bjornspockeli/custom_ble_service_example...
Hello!!
We are carrying out a project using nRF52832 , in which we must send a data to a phone every 1 second for 10 hours. The data sent is a sequence of numbers from 1...
I'm using Eclipse CDT for debugging according to the tutorial on this site. I've installed the device pack and I do see the nRF52 peripherals in the debug view. However all...
Hello Out There,
The Getting Started, it states as follows.
The following steps are required for nRF9160 DK versions UP TO v0.9.0. Newer versions of the nRF9160 DK contain...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
Hi Friend,
I use nrf252832 MCU and SDK 15.3,
I would like to Implement below function,
1:Device bond phone A without password first , the phone A popups a bonding dialog...
Hello. I've migrated my application from SDK 14.2 to 15.1 and I obtain this strange message from peer_manager_handler in my log: I obtain this message only when I connect...
Im trying to enable the Scheduler on a mesh example, but Im getting "1127959>, app_error_weak.c, 108, Mesh assert at 0x0002C9E4 (:0)" each time I try to add or connect it...
Hi,
I want to close uart by using app_uart_close() for low power, but can not init uart again by using app_uart_init() or nrf_drv_uart_init().
More I had try TASKS_STOPRX...
Hi All.
I am trying to use the " ble_advertising_advdata_update" function, but my compiler is giving me the following error. Which class do I need to add?
undefined reference...
