I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
I have an application that works on nrf52832 that when it is powered on is expected to read a sensor data for initial 10 seconds if any, and then start BLE advertising for...
Hello Nordic Team,
I have an application where i am playing some samples over i2s to an audio amplifier. The application also uses fds to store those samples (they can be...
Hi Sir,
In the latest datasheet (52832_v1.4), our reference schematic shows the cap (C6) of DEC2 can be NC.
For DEC2, it is 1.3V regulator supply for Radio, may I know...
Hi
I am giving a try to ESB as an alternative to BLE. I am starting with esb_prx and esb_ptx sample.
That sample works on DK boards.
In order to save energy I would...
Hello to all,
I am using nRF52832 DK with sd132, v6.0.0 and sdk 15.0.0, segger embedded studio. We want to achieve change application timer time (APP_TIMER_TICKS(update_time...
I use nRF52810 and S112 as the soft device. And I use SDK 15.2.0. My BLE device works as a peripheral. And I have to connect some iOS and Android devices with bonding. Communications...
Hello,
I have a problem, I want to measure the power consumption of the nRF9160 with the nRF9160 DK, and I have the N6705B power analyzer, and I like to know how the connection...
Hello dear Nordic community,
We have developed a custom board that contains the nordic nrf52832, which is communicating via I2C bus with a 9-axis sensor (Bosch BMX055...
I am using Softdevice 140 with SDK v15.2 on Segger studio to develope a ble application. when Debugging, the program gets stuck as shown in the attached video. However, the...
Hi, everyone,
We are developing BlueTooth projects on NRF52832 and NRF51822 modules. The projects are built from DFU Bootloader, Soft Device and Main Application. Each one...
Hi Sir,
For EN 300 328 V2.1.1, I reference below setting.
https://devzone.nordicsemi.com/f/nordic-q-a/21643/en-300-328-v2-1-1-receiver-blocking-test-setup/84959#84959...
Hi
I am using TIMER3 and TIMER4 for generating PWM signals using PPI and synchronizing ADC sampling, respectively. I posted the preliminary project in here . After taking...
