I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
Hi,
I want to implement a DC/DC converter setup schematic for my projet and I don't know how to make the difference between the AVDD and VCC_nRF supply tags given in the...
Hi, all!
I have a Quesion about Maximum Voltage & Current of internal DC/DC conv. & LDO of nRF52832.
I'll design circuit using olny internal DC/DC conv. & LDO of nRF52832...
Hi.
Is there a (lazy) (dummy) comfortable way to make an nRF518 chip (in my case, nRF51822) communicate with the built-in bluetooth adapter of a laptop with windows 7 or...
Hi,
I am trying to connect a GPS through UART to nRF52 and get the reading and write it to the serial USB of my PC. I am using app_uart_init() and app_uart_close(). My idea...
Hi, I would like to handle in the twi_event_handler the case when the p_event->type == NRF_DRV_TWI_EVT_EVT_DATA_NACK differently and not treat it as an internal error.
...
I'm trying to use separate antplus network key, but I still can receive messages from devices that are configured with another key. Device A was using network key 0,0,0,0...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
