I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
Hey guys,
I have a little problem on a new board comunicating with a MPU9250 sensor.
Chip version is nrf52832-QFAA-BA
GPIO PINS Used P0.20 (SDA) and P0.21 (SCL)...
The S332 v0.6 has been released and it is supposed to be compatible with SDK11. My concern is that in the release notes of SDK 11, it says "Temporarily removed support for...
I tried the above example but it hangs here:
while (ser_sd_transport_is_busy());
Not sure why, I'm using GDB to step thru code, and it appears always busy...
Is there...
Device: NRF51-DK
I'm using GDB+OpenOCD to step thru code and it appears that the nrf51 resets itself after calling:
SVCALL(SD_BLE_GAP_ADV_START, uint32_t, sd_ble_gap_adv_start...
I want to make rs485 communication with nRF51822. I gone through the UART code, there CTS , RTS pin are required , but for my case tx, rx,rx enable is enough, and also shall...
Hi everybody!!!
I am making a project which use NUS service and I have confuses in connection mode:
when the central and peripheral do not have data to transfer...
Hello, my question is pretty clear i guess. Is it possible to schedule advertising of 2 different packets on the same chip ?
The way i see it, it should be possible to...
