Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I've tried a trivial example (blinky-like, compiled by gcc using proper startup and ld scripts) on nRF52 devkit, but I always only get hard fault.
Debugging through the reset...
The nRF24L01 dataseet V2 (the most recent I think?) states (p.23) that the nRF24L01 can operate on frequencies from 2.400GHz to 2.525GHz . The channel steps are stated as...
I am completely confused by the nRF51 UART. I'm trying to port code originally written for an STM32 (another cortex chip). There, I define an interrupt, enable the RXRDY or...
Hi,
I need to have two different interrupt handler for one pin?
For LOTOHI one handler and for HITOLO another handler, how to do that?
Here is what i did until now...
Hello Nordic and fellow developers
While implementing bonding into an application based on S130 I found it necessary to test on the role of a given connection. Different...
I am getting device id of peripheral on central and then getting it displayed on hypertermianl hyperterminal using ble app multilink perihperal code with multilink central...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
