Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, we are using MAX817048 fuel guage in our project which uses nrf5340 brd. we are using the max817048 fuel guage drivers provided by zephyr in sdk version v2.4.2 to integrate...
Hi, We are currently developing a embedded system utilizing timeslots. When the device gets awoken from deepsleep we want to get a timeslot as soon as possible in order to...
I am using four threads in a application which are main(priority 0), sensor read(priority 6), BLE notify sender(priority 6), ideal thread(priority 15). sensor and BLE notify...
I am currently working on a project using your device (nRF9161), and I need some assistance with incorporating the current date and time into my log messages. Specifically...
Hi, I'm working on a project with a nRF21540DK. I'm working with SDKs and toolchains V2.5.3.
I develop a BLE central following the sdf-nrf/samples/bluetooth/central_uart...
Hi there,
I have worked on visual studio code for nRF projects for many days. It was working fine till yesterday. But now, no project is building successfully. I am getting...
Hi,
We are developing our own board with nrf6190. I already flash the chip with nrf9160dk_at_client_2024-03-13_af2b60d2 application and mfw_nrf9160_1.3.6 modem application...
The customer wants to do wireless approval now, before using the DTM mode, the version available on the old computer is selected, the device can be found on the old computer...
When I click on flash, to flash the blinky program onto the nRF5340 DK board, I get this error message:
FATAL ERROR: required program nrfjprog not found; install it or add...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
Hii,
i used nrf5sdk and i am trying to scanning i2c address of Sensirion sgp40 Sensor but unable to sacn i2c address.
I try SGP40 sensor with arduino code its work correctly...
I have tested NPM1300-EK with NRF52840DK and it works.
However, I am using other MCU with NPM1300 but it is a non -zephyr project.
To work with NPM1300, I have tried...
Hi,
I am using nRF7002 DK. I have set P1.04 as UART RX. For testing I am using TI CC26x2R1 Launchpad to send UART data to nRF7002 DK. I use a logic level shifter board to...
Hello,
I am currently trying to connect an external hardware codec and amp (Adafruit MAX98357 I2S Class-D Mono Amp) in order to play audio via BLE Audio and I2S using...
