Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I tried the radio_test sample with the sdk 2.3.0 on a custom board. I added this to the prj.conf
And this to the app.overlay
With this I had a ttyACM0 and...
I have used ncs-example application workspace to develop our project. In that we were trying to include WIFI, so we include all (sample/wifi/sta) content to my project. but...
Hello,
I recently upgraded the MDK from an "inherited" much older version in my project to MDK version 8.63.1 for GCC. There is now a file called startup_nrf_common.c that...
I used a script to write the Gateway and Headset to the nRF5340 Audio DK board.
I used VSCODE to write the Gateway source and Headset source to the RAYTAC board.
I tried...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are developing a mesh network. Our requirement is the one device can connect to three other devices...
Hello.
What is correct way to use AT%MDMEV commands(searh status) to establish connection after long PSM/sleep time (168h). Our devices are used to track wild animals so...
Hello,
I'm encountering persistent address conflict issues within my Nordic project.
Occasionally, when a device joins the network, I observe address conflict errors....
Hello,
I am trying to send an array which has 2048 bytes via UART. But, when I add a some delay to repeat the the UART transfer, the code gets stuck on the HardFault. I...
Hi Community,
I report this issue in github, it seems nobody reply me, so I ask here again.
lesson 8 exercise 3 solution build failed · Issue #9 · NordicDeveloperAcademy...
Hi,
in our application we use SDCard and USB stack with the following configuration:
The communication with the nRF5340 is done by using a Linux Embedded systems. When...
I think that the source of the nRF5340 Audio DK sample board is designed so that LED1 lights up when a connection is established with CIS.
We are thinking of connecting...
Hello,
I am using the ADC on my custom board, based on nRF9160.
I am getting correct results when measuring a known voltage. However, I noticed that the execution is very...
At the company I work for we are developing a keyboard with mouse capabilities via USB and BLE using the NRF5 17.1.0 SDK. We create the USB HID with the following SDK macro...
