Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi everyone.
For FCC testing we are required to create firmware builds to transmit at the beginning, middle, and end of the BLE spectrum to allow the lab to verify duty...
This happened last month also during debugging of . I could not use my device for the whole month because the quota was gone in minutes.
Now, new month, new quota, I turn...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
I am inquiring about the ability to run two different radio protocols from a single nRF52840, based on this little marketing aritcle by NordicSemiconductor . Specifically...
Hi,
I am using nrf52840DK and trying to implement a weather station application using thingy53 application example. I am using a Bosch BME280 sensor and could read the data...
Hi, we are using nRF52832 for our project. SDK version is nRF5_SDK_17.1.0_ddde560. SoftDevice is S132.
The project requires TWI to read data from a sensor and send that...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
I have two nrf9160DKs that are talking to each other over BLE. Things are working fine but I want to eliminate some of the external noise in my environment. Is it possible...
Hi,
I'm using nRF Connect v2.6.2 with Wireshark (3.6) and it is setup with the nRF sniffer + Nordic network keys configured.
I can decrypt packets from another Zigbee...
Basically I want the nrf5340 to reconnect to a paired peer upon reboot. The code seems to suggest that this should happen via directed advertising.
I am testing this with...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
Is it necessary to use the 32768 crystal on the target device in order to flash that device using a connection to the nRF52 development board, or can the device use the internal...
Hi
this is the error when I tried to connect to peripheral and also get the error on scanning after that connection error
I am using the sample code for this application...
Hi,
I am using nrf52832 to test the function of mcuboot. The reference routine used is D:\ncs\v2.6.0\zephyr\samples\application_development\sysbuild\with_mcuboot. After...
Hey,
I'm trying to follow a few guides on sniffing BLE connections (eg https://hackaday.com/2021/03/23/a-crash-course-on-sniffing-bluetooth-low-energy/ ) with an NRF52...
