Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
hi
I send message from nrf52840_A to nrf52840_B
log shows R eceived CoAP message that does not match any request or resource
Is there a sending format for coap? thx
Hi,
Our product is based on nRF5340 and will run DFU over BLE.
Now I am testing the DFU function via the "Firmware Upgrade" in device manager APP.
In the current architecture...
hi, could you tell why I build SDK17.1.0 (nRF5_SDK_17.1.0_ddde560\examples\peripheral\csense_drv\pca10040\blank\arm5_no_packs) demo code, it appears that mistake (.\_build...
I am trying to send data in peripheral but my central connected to other peripheral .
So I decided to add whitelist in central.
In which function to add whitelist
...
Hi!
I would like to add into my Zephyr project a library called Vanetza , which depends on Boost++, Cryptopp and GeographicLib. I am still learning CMake and I don't know...
Hi
sdk : ncs v2.1.0
example : serial_lte_modem
I used the following command to test and found that sending the character "failed, how should I set it so that I can...
Hello,
I'm working on an application that uses the aws_iot_send function ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/aws_iot.html...
How to make nRF Connect SDK submit to other code management servers (such as bitbucket,Not github), And continue to use Git to manage this code?
I will modify the content...
Hi all,
I recently installed the nRF Connect SDK and have had some success. Very snazzy.
I have seen some issues with the JLink on the DK resetting during firmware validation...
I cannot seem to get floating point supoort for printf/scranf
It works for LOG_INF
I have tried the following .conf settings:
CONFIG_NEWLIB_LIBC =y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi All!
I am trying to program the external nrf9160 SOC using nrf9160 DK using the following connections. Before that, I tried the same connections to program the nrf52820...
When I set CONFIG_LOG=y, CONFIG_SERIAL=y in prj.conf, the UART streams out diagnostic message from my application code as expected, but I also get this endless I2C error message...
I am using NRF52832 for my project.
Refer the following Softdevice and SDK versions.
Softdevice: S132_2.0.0-7.alpha
SDK Version: 4.0.0-2.alpha
Question 1:...
I am using nRF Connect SDK 1.9.0 and the NRF52840.
When building samples/keys/hw_unique_key you get this warning:
----------------------------------------------------...
