Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Since sensor.h API in Zephyr does not support reading hw FIFO, I am planning to use SPI driver to read the hw FIFO on received an interrupt when FIFO has data.
Is there...
Hello
I use nRF9160DK.
Can somebody tell me why it doesn't give an error ( ) if I don't have anything on the I2C line, or how can I be sure if it finds the right address...
I've tested the TX power of nRF52840DKs using CLI application and a sniffer (sniffer device is nRF52840 Dongle). Sent message from one DK to other one via UDP and observed...
Hello,
I am trying to implement the Y-modem protocol to the ble_app_uart example. Basically, I want to send a file from the PC and receive a file in my nrf522840 device...
I use SDK16 with softdevice. Some of its features require hard timings. But it causes hardfault sometimes. It happened at function of gcm_init. My source code is as follows...
Hi
Is there any software that allows to save received Bluetooth data to a spreadsheet? I am using the nrf52 DK running the ble peripheral uart example and received the data...
Hello, after upgrading to SDK version 2.1.0 I noticed that the compilation of all my projects for actinius_icarus_ns always fails:
This is even for projects, where...
Is there a way to initialise a GPIO earlier than in main() without modifying NCS/zephyr code?
We tried an PRE_KERNEL_1 init() function, but this is rather late still.
...
I have two central devices and two peripheral devices each paired with two different services.
I wish each pair can connect only to each other and don't mix up the connection...
Hello,
I am trying to set up for Receiver blocking test for a product that uses both BLE and 802.15.4. The HW is an nRF52840 along with an nRF21540 FEM. I have a couple...
Hi guys,
As I want to debug on my nRF52840 Dongle with a Debugger, my first step was to connect it with internal segger OB JLINK integrated into nRF52840DK. This was not...
Hi,
I've been using the SDK shipped with a vendor product and a feature that I use is to acquire the SPIS semaphore as part of the SPIS handler. The version of the SDK that...
Hello Nordic team,
I'm a beginner on Nordic connect sdk, here have a question about how to increase nrf5340 sending data speed by NUS?
Below is what I testing model now...
Hello.I will open it again because the ticket was closed due to my fault. I want to check the LE Audio (CIS/BIS) function by capturing it as "Airlog" or "hcisnoop" with nRF5340...
Hello,
I am currently working on a project where I need to receive data from a custom board using a nRF52833.
I have made custom characteristics and I can send commands...
