Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I am noticing that particularly with the transmission of bytes over UART while scheduler is running, either some bytes go missing or the entire set of bytes aren't sent or...
Hello
Question: On what clock/clock-speed does the system tick timer run, when configured to use the external clock instead of the CPU clock?
I've seen a couple of...
Good afternoon,
I noticed in the nrfx driver folders there are two differente implementations for ADC: "nrfx_adc.c" and "nrfx_saadc.c"
What is the difference? Why two...
I had successfully interfaced lis3dh on nrf52 dev board using i2c protocol, i am getting raw values of x, y and z but i don't know how to interpret those values i.e. convert...
Hi,
Is there any similar to Online Power Profiler for Zigbee? How much my nRF52840 application should consume when using zboss stack? What is the minimum expected consumption...
Hi all,
I'am doing DFU via OTA
The device will be in bootloader mode ?
my current application has a thread running when i'am initiating DFU via OTA in nrf_connect app...
Hello !
I would like to evaluate few examples from standalone SDK and compile those under Linux Ubuntu.
For example : nRF5_SDK_17.1.0_ddde560/examples/crypto/nrf_cc310_bl...
Hi , I am working with NRF9160. I want to publish 3000 byte(char array) on mqtt server but I get Stack Overflow error. How can I solve these error? I tried these proj conf...
Hello! I currently have an external button and LED connected to the Icarus IoT dev board. For the time being, I just want to turn on the LED in the callback function when...
Hello,
I have a few questions about operation around the nRF9160.
I uploaded a minimal program on the nRF9160-DK card to obtain low consumption.
I get 600uA on average. In...
Hi,
I have implemented the USBD CDC ACM driver into my firmware. What stands out is the latency as soon as the event
APP_USBD_CDC_ACM_USER_EVT_PORT_OPEN triggers, my terminal...
hello. im having issues using ble uart, im planning on connecting my phone to nordic by bluetooth and to pc by usb, the problem that I have is when I use a usb port terminal...
Hi,
We are going through the errata file (nRF52840 rev 2) and wonder how to link anomaly (chip level) with nRF Connect SDK release (RTOS level)...
Where to find the...
Hi!
I am trying to interface LIS3DH module ( https://www.adafruit.com/product/2809 ) with nRF52 DK, SDK 11, via i2c/spi. I tested on Arduino UNO & it gave x,y,z values....
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
