I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hi Devzone,
I use Thingy91. On the nrf9160 side, I run mqtt_simple example; on the nrf52840, I run connectivity_bridge with BLE feature.
When I send "900" via nus service...
I want to control two RGB LED strips with I2S with different GPIO. Not able to figure out how to achieve it. While trying to initialize by separate buffers and data handler...
Hi there,
I have successfully programmed the nrf24le1 on the radio module using the nrf6700 (motherboard) through nrfgo studio. I did so by plugging the radio module into...
Hello,
Is the Power Profiler App capable of calculating and outputting the cumulative energy output to the device under test (when in Source meter mode)? I am using the...
Hi!
There is two things confusing to me about taking IQ samples in AoA application.
1. It is clear to me that that the time between switching of antennae (TSWITCHSPACING...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
Hi,
I am new to the Nordic Semi world, having recently purchased a nRF52840 DK board and a nRF52840 dongle.
I have programmed an Arduino Nano 33 IoT over BLE and when...
We experience a 15-20% rate of dropped advertisements from our nRF52840 device. We have used our own application on our device and the ble_app_att_mtu_throughput application...
I am using an nRF52832 to talk to a Melexis MLX90393 (which supports 400kpbs Fast Mode) via the TWIM interface. I am using the TWI Manager library to schedule transactions...
See the below stack trace using nRF5 SDK 17.0.2, where execution had stopped while entering a critical region during an interrupt event when another log was being processed...
Hello,
I am developing a BLE peripheral with three services:
Device Information Service
Custom service #1 with two characteristics
Custom service #2 with one characteristcs...
When i enable BLE_DFU_SUPPORT_ENABLED 1 and debug i have problem Mesh error 4 at 0x00000000 (:0). I'm using sdk: 17.0.2, sdk_for_mesh: 5.0.0. Board nRF52840 DK. Thanks you...
