Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Dear all,
The forum is full of questions around printing floating point numbers, however, I have a rather strange issue where maybe someone can help.
I have a project...
Hi,
I am new to creating project from scratch.
I want to use nRF51802 module. From few support tickets i have come to know that SDK version 12.3 and SoftDevice S130 version...
This is a beginner question and may well related to a misplaced setting in Segger Embedded Studio.
I am working towards a BLE scanner application which will include NFC...
Hi, Thank you for your attention to this matter.
Please provide nrf5340 layout in this package to me: WLCSP 4.39 x 3.994 mm package The customer needed to use this encapsulation...
I want to receive more than 250 bytes over NUS ,presently i have receiving All Data but in parts of 20 bytes (i.e after receiving 20 bytes BLE_NUS_EVT_RX_DATA event is occures...
Hi there,
I've recently purchased a nrf9160dk to evaluate. I've got some demo code going connecting via LTE and chatting to my AWS server via TCP and that's all going well...
Is there any SPI examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
I want to know the best way to handle time-consuming processes.
I am using an external module used for AT commands via UART. It is necessary to judge the success or failure...
Hi,
Tools used for programming
I am trying to program my custom Adaruit nrf52832 board through NRF connect Programmer.
I am using Nordic nrf52DK to program Adafruit...
Hello,
I need to temporarily hardcode MBR_BOOTLOADER_ADDR address in the code so flash area is calculated correctly in fds.c. I have the following code in my ld file:
...
I'm having issue where after booting I can immediately do three SAADC samples as follows:
This works as expected where I get the callback immediately after the third call...
Hi Nordic,
I have decoded the advertise report below. Will you please confirm my understanding is correct.
Especially
[02] --> NUS_SERVICE_UUID_TYPE
[01] --> BLE_UUID_NUS_SERVICE...
Hello,
I am using the ble_app_beacon example on a nRF52840 dongle.
Without changing the code I am able to load and use it on my dongle.
Now, I am trying to add some...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
