I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hi,
I need a way to have a concurrent connection (multi-peripheral), with whitelisting and bonding. Is there any example of this?
I found an example for multi-peripherals...
Hi!
I loaded up the LTE Sensor Gateway application on the 9160-DK, version 0.8.5. It crashes at the same point every time. I can see it connect to the cloud. When it attempts...
We would like our device to accept "just works" bonding for the first 2 minutes after power up in order to provide simplicity, but require mitm with oob after this to provide...
I have setup my new Thingy91 and got it connected to nrf Cloud. I can see environmental sensor data in the terminal window but it is asking me to update the modem firmware...
Hi, I am using timer capture function to get the current time when i get the interrupt on GPIO.
But it is not returning correct timer value in seconds (Example: for 2-3sec...
Ok so this is an interesting one.
When I got a new PCB with a MDBT42Q module containing NRF52832 I flashed it for the first time (program and softdevice) all the code works...
Hi, I have started development on nrf52840 .
I want to use BLE as a Peripheral . Can you please suggest me which example I can use for sending characteristics and add my...
Hi everyone, I have questions like this: I'm using experimental_lpn example when I want to connect to the friend node when I get request timeout. As far as I know when the...
We're thinking of attaching a battery in the manufacturing process but they may not be programmed right away. Do empty nRF52 modules go into sleep mode when there is no program...
Hi
how to connect one peripheral to two central and after connection established sent the data to both central?
I am using nrf52, soft device 132 .
i am able to make...
Hi!
The nrf5340 PDK I've purchased does not have a mounted "nRF USB" (J3) port, only the debug (J2) port.
Is it possible to do raw USB communication with the USBD driver...
Dear Sir.
I am using the Timer of nRF916 .
In a simple project the timer is working fine ( see attached code ).
A buzzer is connected to PWM output pin 12.
I can...
Dear Sir.
Attached a code .
It takes about 20 seconds from power on until the Blue Led is On.
The timing of the Blue Led is about 2 sec , as in the code.
Commenting...
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
Hi, I'm a beginner with these Nordic DKs. I'm just trying to connect it to my computer and get familiar with the hardware and firmware. However, when I plug in the DK via...
