Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Dear lovely people!
Setup: sdk14 / s132 v5 / nrf52832
Just like with the previous SDKs, I tried to make a multilink nus central fw.
The periph device runs my code based...
Hello,
In our application we heavily use the application scheduler. This was done for 2 main reasons:
serialize access to system resources
enable the soft device to...
Good Afternoon,
I'm writing some config data on an empty record the first time I turn on my board and updating that same record every next time I turn on the board.
...
Hi everybody I have a couple of questions regarding power consumption for the nRF 52 DK Rev. 1 (nRF52832). I currently have an application where I sample 12-bit ADC data via...
I'm working on support for several custom characteristics that require long write support. I'm using the nrf_ble_qwr library, and I've noticed what seems to be a discrepancy...
Hello,
I have an nRF52 DK here that behaves strangely since a few days. Hardware id is 0xc7
When I boot it up with my firmware, sd_ble_enable takes around 2 seconds...
Hi
We have used DTM functionality in nRFgo Studio to carry out signal strength testing during the design stage. We now want to automated this testing in end-of-line testing...
Hello,
I beginner for Nordic board, developing small device using BLE.
I build softdevice, bootloader and application. I checked working DFU mode(via serial, not BLE...
What a software i can use for develloping a Bluetooth Profil Mesh (BLE5) ? Hello every body , i want to develop a bluetooth mesh profil and i don't known which a IDE i will...
Hi,
I make my first project with the nRF52832.
On my first pcb the bluetooth works fine, but this pcb was not fully assembled.
Now i have made a second pcb that is fully...
I need to create and update some data record, the record contains some data that will be updated sequentially or randomly. But the sdk does not execute fds_gc automatically...
I am reading through IETF RFC7668, IPv6 over BLUETOOTH(R) Low Energy . In section 3.2.2, it states the following:
At network interface initialization, both 6LN and 6LBR...
hi
I am really confused For Indoor Asset Tracking which is better Nordic Mesh SDK or Thread
I see Thread Supports Cloud connectivity.
Can the device based on nRF52840...
Hi @ll,
I'm still trying to get the Mesh DFU example up and running. I'm following the guide in the documentation. (Mesh Version 2.0.0: it's the same in 2.0.1 so don't worry...
