Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
Dear Nordic Engineers
Our customer use nRF9160 to develop a tracker.They found that their programs were relatively power-hungry.They tested the serial_lte_modem example...
Hi there!
I am trying to combine the SPI and ble_app_uart examples.
However, when I add the SPI part to the uart, it shows this:
I believe there is some problem...
In the demo in test \ v1.9.0\zephyr\samples\subsys\usb\audio\headphones_microphone , I found that only dual channel 16bit 48Khz audio can be recognized on the PC. the product...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hi
I used Toolchain Manager v0.10.3 to install nRF SDK v1.8.0 at Mac mini(Monterey - 12.1) two times get same issue.
The issue is Toolchain Manager just download toolchain...
I am using the nrf52840 on the Raytac MDBT50Q-1MV2 module. ( https://www.raytac.com/product/ins.php?index_id=24 )
I am supplying the module with 5v USB power to the VBUS...
Hi,
I'm currently trying to use littlefs as the storage backend for the settings subsys and the internal flash for the actual memory. LittleFS is working in general but...
Hi,
I am using two NRF5340 (one as peripheral and one as central) for our project. Both don't have any display and input capabilities.
For our use-case, I would like to...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I've added OTA DFU feature to my application. I flashed pca10100_s140_ble bootloader and my application to my board...
We are using a custom nrf52832 HW configuration and the device is entering a state where it's drawing approximately 3mA without any obvious application layer functionality...
Hi,
I did respond to this:
https://devzone.nordicsemi.com/f/nordic-q-a/86426/peripheral-and-central-uart-sample-crash-when-sending-longer-messages
I do not see a update...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
