Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
Hello there,
I'm using a nRF52840. I would like to perform a complete flash dump. I have tried using an ST Link V2 and and openOCD. It was only returning errors and the...
Hi,
Im using: nRF Connect 1.9.0, Visual Studio Code. I have: a nRF52480-dongle a nRf5340_DK
I would like to have Samples (code), to have a loop through with the highest...
i have a code base which is originally run on nrf52832 dk and i want to port it to the pca10059 dongle i run in gcc env and successfully modified the definitions and includes...
Hi, I'm developing an project based on ble_app_uart example. My expection that is multi mobile phone can connect with my nRF. But, my nRF can connect and communicate with...
Hi Nordic! I'm using the nRF9160 with a micro sd card so I have a lot of storage. I was wondering if it is possible to retrieve a .hex file and flash it using LTE?
I'm able...
Hi,
When I try to build a 'light_switch' project on SEGGER embedded studio for nRF connect SDK 1.9.1 for BMD-330-EVAL board. Running into the following error
arm-none...
Hello Everyone,
I am using NRF52833 in my project and I have my NRF module connected to 2 other microcontrollers on UART peripherals. The details are mentioned as below...
We have first worked with a development kit from Nordic (nRF52840 DK) . We flashed the BLE applications using the nRF Command Line Tools.
https://www.nordicsemi.com/Products...
Hello,
I have to open a new discussion session on the same topic because the current session has been closed.
The topic is as follows: devzone.nordicsemi.com/.../at...
Hi,
We currently have a Gazell project that runs on nRF52832 . We have difficulties changing the project target to the nRF52810 .
From the SDK17.0.2, example: "gzll_ack_payload_device_pca10040...
Hi,
I have a firmware (performing DFU over Bluetooth )that runs well on nRF52833 dev kit and for developing the DFU over BLE. I follow this tutorial
https://devzone.nordicsemi...
Using SDK 17.0.2 I wrote a function to modify advertising interval on the run. The function doesn't return any error but the interval isn't changed. What am I doing wrong...
After nrf_drv_twi_tx() function and nrf_drv_twi_rx() function, m_xfer_done is checked using APP_ERROR_CHECK(m_xfer_done). What is the significance of checking m_xfer_done...
Hi,
I am working on DFU-OTA example on BLE. my doubt here is once the controller copied the image into slot1 bootloader will immediately start to validate whether the image...
I am using the following code to generate and output a n-MHz clock on a GPIO pin. (code is borrowed/copied from another question on this forum)
However, the clock output...
