Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hello,
I am working on a project which is based on nrf52840 and Zephyr.
Current prototype uses Adafruit nrf52840 sense board with spi based display attached.
I am new...
Hi,
I experience a very strange issue with UART.
When I try to send data via /dev/ttyACM0 device it looks like the characters sent are buffered and sent only upon the...
Hi! I am in the process of trying to install the Asset Tracker on my Thingy91. I have got it to work with nrfCloud and I am now trying to configure it to use the AWS backend...
I am using the nRF52 SDK : nRF5_SDK_17.0.2_d674dde
- When data are all ASCII-Hex (0x30) the code working fine
- Now I try to optimize code by changing to binary data....
I have been using the nRF52-DK for while and it been good.
But when I accidental hold the "BOOT/RESET" button, the board now stop working. only LEDs is blinking (per sec...
I would like to ask if someone from India ever used Thingy:91? Which SIM card is used or where to get the supported SIM card? How to get it working in India?
In VS Code, when pushing the " Connect To RTT In nRF Terminal " button, a message shows up:
J-Link V7.20 Device Selection The selected device "NRF52832_XXAA_REV2" is unknown...
Goodday all
Im trying to drive some Neopixel LEDs with 52840DK SDK_17.1.0. and have been following this example. https://devzone.nordicsemi.com/f/nordic-q-a/70560/nrfx_i2s...
I'm trying to install and run the nRF Command Line Tools, but am running into issues. I was able to successfully install the Linux32 version of the tools, but when I go to...
Hi
I am using nrf52840 and I want to use nrf_calendar example with app_ble_uart,
I am traying to send parameter from nrf toolbox uart app mobile
but I have no idea how...
Hi,
I am using nordic 52840 development kit along with sdk17.1
I am tried to use ble-uart example code to receive data from the app and based on the data i need to write...
I'm trying to follow the instructions to perform an OTA DFU for the Thingy 52.
https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/dfu_generating.html...
I'm using SDK 1.7.0. Here's how I have the modem code setup.
Init modem outside of thread loop
Set modem at+ comman CFUN=1 (start searching for a tower)
Once +CEREG...
