Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi,
I want to define two different channel for I2C and interface two slave devices. nRF52840 will always be master in this case. As mentioned in the Product Spec. of nRF52840...
Hi,
I have a 128bit UUID on the ad block which I need to change on the fly to another 128bit UUID.
I tried different solutions and searched for a good example, however...
I want my device to blink a LED periodically when there's a BLE connection. This BLE connection will usually be idle and every now and then there'll be heavy traffic back...
I'm working on a project & I followed the procedure found here
in the answer, it works with me when I tested it when pairing from the bluetooth devices shown, when I tested...
Hi,
I am using nrf42840 dk board,sdk 14.2 and keil IDE.I have integrated bmp180 sensor code with ble_app_proximity code.I have no errors.After loading the code,I am getting...
Hello! I am migrating ble_mpu_simple code from sdk 14.2 to sdk 15.2.While migrating,I am getting the error.
error: #20: identifier "SPIM_CSNPOL_CSNPOL_LOW" is undefined...
Hi team,
I am using nrf52840 Development Kit,sdk 15.2,Keil IDE
I am using MPU6050 sensor.For that,I used nrf5_MPU_examples_master file.
I have integrated ble_mpu_sensor...
Hi,
i was looking for nrfjprog command line tool on nordic website. But this tool not available to download. Is this tool got replaced?
If yes, then which is replaced...
Everybody is good !
I want to know whether BLE can broadcast, connect and communicate normally when nrf52832 communicates with nrf24L01.
The data manual says that it supports...
Hi,
After long time again started working on nordic controller's. Previously my pc was properly configured for NRF5x environment which includes gcc and flahser.
Recently...
The pin connected to lis2dh12's int pin consumes about 300 uA.
But the pin I used as button,also enabled int function , works good.
The pin I used as wake-up is in input...
In order to establish a wireless connection from my pca10056 developing card and a second nRF52840 SoC module using example CLI commands, and then being able to check/set...
Hi,
I have few queries regarding the internal regulators of nRF52840.
1) Is it mandatory to configure the internal LDO or DC/DC regulators of nRF52840 ?
2) If these...
Hi,
As mentioned in the Ch. 5 "nRF52840_DK_PB_v1.0.pdf" Section 5.3 in "high power mode the external supply should be connected to just the "VDDH" pins and "VDD" pins not...
I want to write to nRF52840 the example "ble_app_hrs_pca10056" from nRF5_SDK_15.2.0 by command line.
first I merge 3 hex file (bootloader, softdevice and app) with the command...
