hi support team,
may i ask do we have demo on how to test remote provision in ncs2.9.0?
i assume there are two possiblilities:
1.
For server, we need add below settings...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi
We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
Hey,
I’m currently evaluating DECT NR+ using two nRF9151 DKs with the nRF Connect SDK v2.9.0.
According to the ETSI specification (ETSI TS 103 636-4 V2.1.1), the Physical...
Hi,
I need to use two or more different event lengths for different modes. The event length should be set based on the mode before establishing a connection. I found that...
I would like to know how to add an eSIM profile to an eSIM chip using the nRF9151 modem. Is there any platform or support that enables an infrastructure for this? What should...
Title: Issue with I2C (TWI) Communication on nRF52840 (SDK 16, Segger 8.2a)
Description:
I am working with the nRF52840 using nRF SDK 16 in Segger Embedded Studio 8...
Hi
is there an example for this: sending data over ISM band 2.4 gHz without BLE on a NRF52840 or similar?
I need to transmit 2 bytes board to board with jitter and delay...
Hello, I want to write an applicatin that gets at_coammnds from the terminal via uart, sends the command to the modem and then sends the respond back via uart. I have two...
Please provide an example of using app_sched_event_put() to pass a string.
This is what I have at present:
The handler appears to get the first 4 characters OK (perhaps...
Hello,
We have a sensor with 2 ADCs inputs meauring identical LMT70s on the board. With one of our older firmwares we get the accurate valudes of 22deg or so on both channels...
I am trying to install the toolchaing under Ubuntu 24.04LTS.
Installing via the toolchain manager does not work. I get the following error.
Failed to clone the repositories...
Hi,
The version of the nrf connect mobile app is not 4.29.xx but 4.26.xx.
The dfu generally succeed on our target however sometimes it failed on another target device...
We use nrf52833 chip but I don't know which SDK and version.
but I used "s113_nrf52_7.2.0_softdevice.hex" in our project having started on 2021.01.27.
So, It's old project...
We tried to see device logs from our target.
We use dfu bootloader for our custom target.
I enable RTT logging on our custom source for our target.
Then we can see...
Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
If anyone has successfully stored and retrieved settings on the nRF52840 dongle using any method, please share your approach.
I'm trying to store and retrieve settings...
1. Description and how to recreate it
Im attempting to flash a custom board with a nrf5340 on board using mcuboot via nrf Programmer v4.5.0.
When I put the board in bootloader...
