I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi,
Thinking of connecting Custom hardware made of nRF5340 + nRF7002 to the windows laptop using Python code. I already have nRF54L15DK with nRF7002 EBII expansion board...
I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Hi,
I am developing a custom PCB based on the nRF52840 and am currently trying to flash/debug it using an nRF52840-DK (PCA10056) as an external debugger.
connected devices...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Hello,
How to config FEM on "nRF21540-DK" to set the TX power as +20dBm ??
I used the "perpheral_nus" sample (basic Bluetooth LE sample) in NCS 3.2.4 version
Also...
Hi,
As the subject says, I have an nRF54LM20A acting as a SPI slave. When I perform a call to spi_transceive_cb(), I don't have any data for TX (i.e. MISO). This runs until...
Hi,
I have bought an nRF52DK (PCA10040 v3.0.0), which has an nRF5340 chip.
I want to use it as BLE Sniffer to debug my application, but Wireshark is giving me an error...
Hi, I need the nRF91 SiP SUPL client library (for A-GNSS via SUPL on my nRF9151, NCS v2.9.1). The official download process is not working for me, same problem many others...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
Hello Nordic,
I am working on nRF52832 with SDK 17.1, using ESB, I previously used UART for DFU updates, but now I need to perform OTA updates via ESB.
I noticed a macro...
I want to fix the problem of insufficient time windows when I search for a fix. I know that the recommended way is to use priority mode + EDX + PSM, but I tried to just turn...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
