Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi all!
I've been working on a project using the nRF Connect extension for VS Code and I've been trying to figure out which HEX file in my build/zephyr folder for my application...
Hi,
I am sending a SCAN_REQ packet from my code after receiving an Advertising packet from the NRF5340 DUT. Sometimes I receive the SCAN_RSP packet, but other times I encounter...
I am working on a project where my hardware includes an array of LEDs. I want to run an LED pattern on the array during the DFU process. I have tried to find a solution for...
Hi, I have been working with I2S Mic sph0645lm4h-b and nRF5340 audio DK. I configured mic and while I'm reading the data it throughs an error code of -5. I'm Sharing the code...
I am a beginner and I want to switch from SDK 17 to nRF connect SDK v2.6.0, but I found that many configurations are different, such as gap initialization, gatt initialization...
Hi,
In my wearable application, I would like to have reset functionality by pressing two buttons, which I also would like to use as application interrupts. I read that the...
I'm working on implementing asynchronous UART on a nRF52840dk but uart_callback_set() is returning -88 (ENOSYS), which according to the tutorial here means it's not supported...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
I attempted to use https://github.com/Protocentral/protocentral_max30001_zephyr_driver to build my project. However, I am still encountering some issues.
1.In the overlay...
Was following steps here to set up the sidewalk sdk from a blank nRF Connect SDK for VS Code application template using sdk v2.7.0. I noticed immediately that the directory...
Description : I am experiencing a build issue after porting my project from nRF SDK 2.4.2 to nRF SDK 2.7.0. The project involves using the nRF5340 and was building successfully...
Hi,
I'm trying to implement an application that acquires data from two channels of the SAADC in "parallel". I'm currently using the nRF52 DK and nRF5 SDK v17.1.0. After...
when I change from compatible = "nordic,nrf-spi" ; to compatible = "nordic,nrf-spim" ;
the SPI transceive failed
my overlay file
my yaml file
main code
