Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I am trying to run the NCP light_zc sample (with nrf52840 dk on usb) on latest RaspberryPI 4 (aarch64)
The sample starts, does some communication on usb then the nrf reboots...
Hi,
I am trying to use the UART on my nRF9160DK board.
In my program I have 2 uarts in use. uart0 is used for printk output and uart1 is used to receive data in async...
Hello! I'm working on an application with precise timing and I'm using timers and PPI.
In the callback pulse_end_cb() I seem to get garbage instead of the parameters, which...
Hey, so we have been building a prototype similar to a hearing aid with the nRF5340 Audio DK. I had a few queries regarding the DSP block of CS47L63 Hardware Codec which is...
Hi,
I'm implementing a BLE GATT peripheral that has no display but it does have a button.
I'd like to make some characteristics only available to devices that are BONDED...
Hi,
I am using CJSON_LIB from nrf-sdk modules, I even tested this cjson lib in such a simple way in helloworld app (I attached the sample project.), and after running for...
Hi!
We're looking into possibility to use nRF5340 and nRF7002 to provide BLE and WiFi access to an external MCU. The idea is to use one of NXP's MCUs as the main processor...
In the Power Profiler, when I select a larger area in the data logger, then it stops updating the selection time. It works great till 16:40m, but then stays at this value...
Hi,
We have developed our code against SDK 2.3.0 and I wanted to try to upgrade the SDK to 2.6.0. I had to remove CONFIG_OPENTHREAD_CHILD_SUPERVISION from my prj.conf, but...
HI
I basically define uart_init(); in Main.
And use DEBUG below to decide whether to use UART.
#ifndef DEBUG
NRF_UART0->TASKS_STOPRX= 1; NRF_UART0->ENABLE =...
In the transition from SDK v2.5.x to v2.6.x, Nordic removed support for boards that don't have the nonsecure (_ns) configuration in the Azure IOT hub sample. In other words...
Hi
I developing a nrf9160 project and try to use FOTA, I reference to example /samples/cellular/nrf_cloud_rest_fota.
finally firmware can successfully downloaded
...
I'm learning to use the Zephyr toolchain and in the interest of connecting the Zephyr-side coding to the i2c protocols I am familiar with, I have some questions.
I'm trying...
I have my software set up so that it does some computation within the Attribute write callback function like this.
b roadcastKeyHandler does somewhat of...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. The board has an RTC, LSM6DSO as IMU, an opamp front end for the analog inputs...
