Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hiya,
I am currently going through the nRF Connect SDK Fundamentals Lesson 2 (section: DK devicetree file) and I am stuck. In the example given, it says:
" These hardware...
It's great to have a public forum with Nordic engineers helping out but the DevZone web experience leaves much to be desired. The editing is painful enough that I really dislike...
We are using nRF54L15 devices and have enabled secure boot . Our current setup is:
Firmware images are signed with a private key
The corresponding public key is...
Hi,
I am trying to use lvgl on nrf54l15, but I am facing issues with spi. I was trying first to use vanilla zephyr 4.1, but now I switched to ncs 3.1.1. I am trying to run...
Hi
I'm using two nRF5340 Audio DK's for my university project. I'm just trying to familiarise myself with the audio examples by sending audio from one kit to another but...
Hello, I am facing an issue of low speed of file read and write while using LFS on External Flash, Winbond (W25Q64JV) .
This is the Configuration Im using in my DTS file...
Hi,
Just received a nRF52840 connected it to my Apple Silicon Macbook (maybe relevant?) which is running Sequoia 15.2 via a USB-C to micro cable.
When I powered it up...
Hello,
Setup:
nrf5340
ncs 2.9.1
Zigbee r23 add-on
I’ve implemented a custom ZCL cluster that acts as a data pipe. I’m trying to determine what the actual maximum...
It would be nice to be able to provision the KMU of nRF54l15 devices directly from the nRF Connect Programmer Tool. This is currently only possible using the nrfutil command...
Hi: Nordic Team
Environment: - SoftDevice: S332 (SDK16), ANT+ + BLE on nRF52 - Calling ANT APIs from app (e.g., sd_ant_channel_status_get, sd_ant_channel_rx_search_timeout_set...
Hello everyone!
I want to use BLE with the filesystem (FS), but I haven’t found any examples. When I enable BLE advertising, any filesystem operations stop working.
(...
Hello Nordic team,
I'm working with nRF Connect SDK (version 3.1.0) on an nRF54L15 device and using mcumgr for Bluetooth LE firmware updates via the SMP service.
My goal...
Hi,
I'm trying to run the nrf/samples/cellular/at_monitor sample (v3.2.1), but I keep getting this output.
I have two nRF9160 devkits, and they both are giving me this...
Hello,
I'm using the NORA-B106-00B-00 (nRF5340) on a custom PCB board. I can program the board, but there is no output i.e. print statements coming out of the board...
