Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
Hi,
I'm using nrf52840 in revision 3, which has protection access port enabled by default.
My application is built with SDK15.0.0 / SDS S140 6.0.0
In order to get debug...
Hi,
I would like to receive notifications from iPhone to nRF54L15-DK over BLE. Anyone in the nRF community tried iOS notifications over BLE to tell me how it is done please...
Hello,
Current Situation
We are working with an nRF5340 device running nRF Connect SDK v2.7.99-cs2 . BLE security is configured for Just Works pairing (Security Mode 1...
Dear Nordic Team,
I am using NRF54L15 on NRF54 DK board and when trying to use/activate any other UART other than UART20 (e.g. UART21, UART22, UART00) on my project, every...
Hello, I've been developing an nRF52840 on a custom PCB for ~1 month now, and my environment was working previously. After updating my version of Jlink and installing other...
Hello.
I'm using nrf9151 with nRF Connect SDK v3.1.1 and Zephyr v4.1.99, modem firmware v2.0.2 I try to implement the full modem update. After downloading the "firmware...
Hello,
I can no longer use AT commands on my nRF9161 DK development board.
It used to work perfectly, but I don't know what happened.
I had previously completed the...
Hello,
I wanted to see if it is possible to move provisioned devices between team IDs in the NRF cloud. Right now I am using a nrf9151 to connect to the cloud. Once the...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board.
My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
