I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I added two extra buttons to ble_app_blinky (SDK 17.1.0) - port 1.10 and 0.31 I am running the code on an nRF52840 Dongle. The additional buttons are configured exactly like...
Hi,
I am using the sensor server example available in nrf5 sdk for mesh to build my own application on top of it. And the SOC we are using is nRF52832. I am trying to erase...
I see in the nrfx_uarte.c file the statement NRFX_LOG_INFO("Transfer about to send : %d bytes", length);
How can I set the logging for this file on?
#define NRFX_LOG_MODULE...
Hi,
My apologies if this is the wrong place for this.
I've been using the Power Profiler with the PPK2 and I'm very happy with the product, just have a couple small suggestions...
Hi there! I am facing " <err> download_client: Unexpected HTTP response: 400 bad request" error whenever I am trying to download full modem update from AWS S3 bucket. My environment...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
Hi,
I moved my code on a second windows pc, checkout the code from git,download the same nordic sdk and softdevice version, same SES version but running on my board, the...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
Hello,
I want to use standalone logging for each file (/module)(/driver) of my program, therefore register different logging modules with different log levels each. Registering...
Hi,
I am attempting to configure a nRF52840 (packaged as Seeeduino XIAO Sense) for the popular printer software Klipper.
i have the following processor options and am...
Hello I'm trying to use GPIO pins as UART on the nRF 52 DK rather than the default UART pins. How do I change the pin configuration? I'm using nRF SDK version 17.1. 0
