I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
I use the modified version of the USBD example(nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd) in nRF5 SDK from here . (My development kit is nRF52840DK.)
And I...
Hi, I have configured normal uart, where you send 1 tx_buf and wait for the rx_buf until you get a response. This setup was fine until the logging feature was requested. However...
Hi, I am developing a product using BLE with nrf52832. We are aiming for a BLE communication range of around 1.0m. However, if txpower is set to -20dbm, BLE communication...
Hi,
I found this forum post about the Verizon APN:
https://devzone.nordicsemi.com/f/nordic-q-a/46288/nrf9160-verizon-sim
This implies that I don't have to use "AT...
I want to parse the following JSON { "ver": 3, "mode": "online", "custom": { "apl1": [ "off" ] } }
Tell me about how to parse json and how to write code
The keywords...
Hi Everyone,
I am developing a PC App. with nrf52840 usb dongle (central) to communicate with nrf52840 BLE device (peripheral) on long term and transport data. Everything...
Hi,
I was working on nrf52840 DK and I left it a few weeks and came back to use it and I discovered that the whole USB connector (J2) got removed. Not sure if there are...
To the kind attention of Nordic support team,
I'd like to know what would be the best theoretically way, if possible, to control "when" multiple notifications are sent...
Hi,
I am developing with the nRF52833 DK using NCS v2.00.
I have edited the existing TX power service (TPS) to allow the client to set a desired TX power. I have added...
I'm using the nRF52840 with NCS SDK 2.0.2 and need to be able to change the BLE advertisement name of the peripheral device dynamically.
I have this working when using ...
Hello Devzone,
I am building firmware for an nRF9160 based device, starting with an ncs 1.6.1 sample app and LTE modem firmware v1.3.1. I'm in North America, and when testing...
I am using the SD card driver from nRF5 SDK v17.0.2. Device nrf52840, IDE Segger, Custom PCB. nRF52 DK as progremmer.
There are problems when deinitializing the SD card...
Hi,
I am developing a peripheral in ble, and I receive the following error when I disconnect a new connection within the connection callback.
bt_conn_disconnect ( conn...
Hi,
I'm writing an application which, depending on configuration, will either use ESB and Bluetooth, or just ESB.
I read through the article ( ) describing how to use...
