When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
I use the NCS version 1.9.0 with SES.I build and flsah successfully.I use the antenna array with 4x4,about 16 antennas.
In Tx,i use the Putty to debug serial.there is it;s...
Hi,
I have a hardware that I want to connect via BLE and send data via NUS (Nordic UART Service). I can connect to this hardware via the NRF Connect application on android...
Hello.
I get an error NRF_BREAKPOINT_COND. I use nRF5_SDK_17.0.2, s132_nrf52_7.2.0_softdevice and my kit - nRF52-DK.
An error occurs when trying to swap UART pins (Change...
Hello,
I want to establish 802.15.4 communication @ 1 Mbit between a nRF52840-DK and an ATmega256RFR2 based device. The communication works well with 250 kBit/s in RADIO_MODE_MODE_Ieee802154_250Kbit...
Here is the situation:I can read the accvalues by uart without the ble, but when I was trying to read the values on the phone with the ble, it didnt work. I modified the official...
Hi,
I use event manager and define semaphore according to https://docs.zephyrproject.org/latest/reference/kernel/synchronization/semaphores.html . How can i delete the semaphore...
Hello!
I have an incremental encoder such as this one: https://www.digikey.no/en/products/detail/cui-devices/AMT103-2048-N4000-S/10468125
I have to make this work with...
Hi,
I have loaded one of the basic samples( nrf connect SDK, fade_led ) into my nrf52DK.
Using the free run mode or the debugger almost everything seems to work correctly...
