When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
We recently bought a nRF9160 Eval board and are planning to connect it with a STM32H757XI_M7.
We would like to know, how well it can be integrated with the IwIP Stack...
Hi Nordic,
I am using the SDK 17, s140 and the nrf52840 , with a modified multilink NUS central example. The intention is to print over UART as fast as possible all data...
Hi All,
I have a nRF9160 custom board connected thru the P19 debug out connector to the NRF91DK board.
How do I 'make' the NRF91DK debug the custom board nRF9160 and not...
Hello. I have a custom board which contains S32K148 MCU and Murata MBN52832 BLE Module and several other modules like GPS, LTE etc. Board is powered via external 12 V adapter...
Hello. It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to know the handle value of the characteristic set as Generic Access and...
Hello,
We have a bunch of demo devices that were populated with the nrf5340 eng A version. So far we have been able to make them work by using nrf connect SDK v1.4.0 which...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
Hello,
I am using the nRF52840 DK board and with Softdevice code nRF SDK 17.0.2. I am trying to write custom advertise data with custom type.
As you can see in the above...
Hi! Hope you are all doing well,
I'm having trouble making a project from scratch, I'm basically trying to filter bluetooth devices by manufacture code but I'm afraid that...
Hi All,
This has happened before so I know it's a handler error.
But this time I'm pretty sure my handle is not wrong, can help me?
in main.c =>
Best regards...
