I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
Hello
I'm asking a question because there's a part that doesn't work well while using ble_nus_data_send().
There is a problem sending continuous data to the app using...
Hello
Sorry this is a basic question and I shouldn't be bothering you with this but I have already dealt with a number of issues with Segger so I couldn't resist. - I have...
Hi, I open ssl socket to the server (without certificate verification), and then use an http_client_req() call, to perform the actual http request (with additional optional...
Hello Team,
I am trying to port the example of nRF5 SDK for Mesh to IAR Embedded Workbench for ARM (Dev Kit (nRF52832).
I am using nRF5_SDK_17.0.2_d674dde and nrf5_SDK_for_Mesh_v5...
I'm testing the Serial LTE Modem application on the nRF9160DK with the LTE Link Monitor. I want to use the DK as a UDP client to send data
to my remote server via UDP over...
Hi,
I am working with a custom board that has an nRF9160 SiP (B0). I am using SDK v1.6.0 on a Windows 10 machine. Modem FW is v1.2.3.
Our device uses GPS periodically...
Hello all,
I'm trying to use P0.05 (AIN3) as output, but it does not work.
in file .dts is used as: rts-pin = <5>; status = "okay"; of uart0, I have to change this config...
I'm evaluating feasibility and developing a Proof-of-Concept for a client using the NRF9160 + NRF52840. This is a second generation product where the client wants to evaluate...
