In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Hi,
I'm trying to develop a Zigbee application, and following the guide provided here for adding a ZCL cluster to the Zigbee template. However, I think this guide is not...
Set up: Rpi Bluez 5.72 (provisioner)
nRF DK (light example)
steps:
1) trigger scan un provisioned devices from Rpi
2) able to see nRF device in scan results
3) start...
Hello,
currently I'm migrating a project from connect SDK 2.6.0 to 2.9.0. After some changes according to the migration guides the project builds fine and also runs.
As...
I would like to use nRF52832 DK to test Nordic UART Service (NUS). But west build failed with the following messages. What is meaning of "zephyr_pre0.elf section `noinit'...
Hello,
I am attempting to use the nRF7002EK shield with my nRF54L15PDK development kit.
I have custom code, but it's based on the wifi scan example provided by Nordic...
Hello,
I would like to know if there is a way that I could see the source code of the nRF Mesh Sniffer app for Android, just like the nRF mesh source code is available in...
Hi, I am currently using the nRF52832 MCU and have implemented hard fault handling as follows: I use the macro APP_ERROR_CHECK(err_code), which, in case of an error, calls...
Hi
I am trying to perform a full modem update on my nrf9160 DK board.
I started at v1.3.4 and successfully used the partial update method to go to 1.3.5
I then used...
Hi everybody, I'm looking to build a PWM generator with 2 outputs from 1-100Hz. Unfurtunately the current PWM API examples with Zephyr works only for 4-100Hz.
I've tried...
Hi,
I have just bought a PPK2 and (mistakenly on my part) assumed it must read the Voltage of the output as well (necessary for power measurements). I see now that it doesn...
I am using ncs sdk, my projects are under ~/zephyr-workspace. This is from an example project - blinkypwm. The clangd compiler shows the following erro: In included file:...
I try to simultaneous update (app + networkcore) with usb and external flash on my custombord And serial recovery, not DFU from app.
this is mcuboot config. I have set the...
i want to commission matter compatible smart switch into thread network.
but i'm getting internal error .
but other device like matter samples light_bulb (nrf52840dk)...
