When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I need to monitor how much heap was ever left available, as a minimum, after I have run my CI test suite. This is the true minimum heap ever remaining, so taking account of...
Hi -
In reading through the data sheets for the Nordic chips that support the low-rate (125 kbps) BT 5 PHY, I'm seeing Rx sensitivity numbers around -103 dBm. For the 1...
Hi,
To manufacturer production I would like to use the nrfjprog.dll in order to make an WPF C# application to program our NRF device.
I would like to use your nrfjprog...
Hello,
I am working with the nrf52832 chip and wanted to know if there are any pins that are shown on the schematic diagram, that I should not use to ensure that the Bluetooth...
Hi there,
In my application I need to send varying amounts of data (1~8KB) and store it in RAM. I trying to use memory manager library to replace the malloc() and free(...
Hi there,
I'm having some trouble piecing together an app to use V2 of the NRFX SAADC API, compounded with this being my first time using the SAADC functionality on an nRF...
I've tried to update the firmware on my Thingy:91 to version 1.2 using the file mfw:_nrf91060120.zip:
I set the Thingy:91 to ' application serial recovery mode by pushing...
I tried to play with nrf52840 and ade7953 .
At the begining, I use PC uart application to do the following test and everything works well. Here are the testing steps: 1...
I have the CLI module over UART enabled, with one command that continuously prints out the readings from a sensor. What I'm trying to do is stopping this continuous printout...
Hi,
I am using the nRF52832 and am going at it barebones because I cannot for the life of me get the SDK to work. I am using the nRF52832 manual.
-> Manual
I have two...
Hi, Im using a nRF52DK to read LIS3DH accelerometer readings in putty. Im new to this platform, I tried couple of example programs like blinkey, uart, and button in BLE. Now...
Dear All,
I am trying to implement a simple data recorder on nRF52840 DK that digitizes signals over SAADC and writes them onto the SD card. The program is working fine...
Hi,
Does anyone know where to find the BLE backwards compatibly of a given soft-device ?
I have looked at the PDF document given for my soft-device version S132, and...
Hello,
I am running an application on the s140 soft device using the buttonless dfu as an example. I am using the dual ramp pwm scheme to generate complementary pwm waveforms...
