I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I want to try register level programming of Nrf52832 i.e low level programming. I referred your This GitHub repository but there are sill some libraries used . Is there any...
I am running an application with norma NUS Service with bonding.
When I want to make a DFU I start to write a token into the flash with fds and then do a soft reset. After...
Hi, I'm using nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 to develop a Zigbee Network. I'm using the ble_zigbee_template example as starting point of my works. I seen that...
Hello,
I have an nRF9160 DK and a Thingy:91. Both have been running asset_tracker for more than 3 hours, but none achieved an LTE Connection. I have installed the latest...
Hi, i am working with usb cdc driver (sdk 15.3 and nrf52840) and i have a problem . This is my variables initialization APP_USBD_CDC_ACM_GLOBAL_DEF(m_app_cdc_acm, cdc_acm_user_ev_handler...
Hello,
I send SMS from nRF9160 to my number using following method.
1. Open LTE Socket
2. Send AT Commands:
a. AT+ CFUN?
b. AT + CFUN = 1
c. AT+ CFUN?
d. AT...
Hi all, If using the RC LF instead of a 32.768KHz crystal are there any side effects of the 16ms calibration period which occurs every 4 seconds? I'm mostly concerned how...
Hi,
I am working on buttonless dfu example, but i want to design my application in such a way that, device should enter into dfu mode when button is pressed. I should be...
Hi, I have some issue about mesh network.
Using below developing environment.
- SEGGER Embedded studio for ARM V4.22
- nRF SDK 15.3.0
- nRF Mesh SDK 3.2.0
- chip...
Hello
I'm a beginner in Bluetooh and I bought two dev board NRF52840 DK. I would like to make a mesh with these two boards. One in master and the other in relay, the goal...
Hi,
I´m working with "TWI Sensor" example of SDK 16 and I modified the Main function of main.c as follows (just added NRF_LOG_INFO("\r\ntest") );:
I just added this...
Is there a good way to uniquely identify mesh node across multiple smart phones? The problem is: Android provides access to MAC addresses that can be used as identifiers of...
Hello. When I examined the BLE data format, I found that it was as shown in Figure 1.
Fig1
I am using NRF52832, please tell me how to detect the CRC value...
I am using mbedtls with ECB hard accelerator on nRF52840. So I changed the macro definition: UPDATE_CBC_MAC in ccm.c to function:
#define HT_UPDATE_CBC_MAC \
for ( i...
