When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I have brought nrf52840 preview dk ,it is not getting detected by the computer nor its power led getting light up. Last code i tested on its was blinky.
I doubt it has any...
I have a custom board that I have programmed using the UART_BLE example. The code executes and I know I am advertising since LED1 blinks meaning it is advertising but for...
I am testing the Sensor example in the Mesh SDK.
For my implementation I need three properties that are given by the BT Mesh specification. (Properties 0x004F, 0x0057, 0x0059...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
Hello DevZone,
PCA10040 SDK 15.0.0 SD132
I written my own SPIM driver which uses the list function to read in a few bytes. I've set up my list as the example in the...
Hi,
What is the difference between performing a reset by using the function sd_nvic_SystemReset(), and performing a reset by turning the power voltage off and then turn...
I used "nrf5_SDK_for_Mesh_v4.2.0_src.zip" and "nRF5_SDK_V16.0.0", When I used scan_start() command, I saw Light_Switch_Server device and Light_Switch_Client device on the...
We have fabbed a PCB for the nRF52840 that has a QSPI chip. The pins are different from the example in the SDK. I was trying to get the SDK example (examples/peripheral/qspi...
Just test SDK17.0.2 serial DFU demo project on Nordic PCA10100 board by USB serial.and use s140_nrf52_7.2.0_softdevice.hex
Got below exception. Any clue for it please? ...
Hi,
I have my application based on nRF52840 device.
When writting a wrong passkey, my device is reseted.
Which can be the reason? I have already implemented event PM_EVT_CONN_SEC_FAILED...
Hello
To calculate the definite yaw value of gyro, I would like to use the mpu9250 with magnetic sensors. I used Martinsbl's nrf5-mpu library when I used mpu6050, can I...
Hi there,
what is recommended strategy to read/write data on uart?
Taking from sample, read byte-by-byte, on 115k, sometimes data are truncated.
Is there a possibility...
Hello,
I developed a thread network using the latest SDK for Thread v4.1. I also have the latest OpenThread Border Router running.
I cannot ping Google IPv4 from my Thread...
Hi,
I'm using nrf52840DK as a central device (sdk16 ble-app-uart-multilink-master) and my peripheral device is bt840 chip(sdk15.2 ble_app_uart_pca10056_s140).
My peripheral...
