Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, all
I'm using nrf52832 pca10040, s132
I've asked several questions, but I haven't found a solution yet.
I want to send data through uart to the custom board.....
Hi,
I am trying to extract the static MAC address from a 52832 using NCS.
I do not want to try to read directly DEVICEADDR[0] or 1, but use a clean function.
I tried...
Hi People, I hope I can get help here or get pointed to a right forum where this can be answered.
I am using u-blox NINA-B306 (based on nRF52840) in one of my custom made...
Hello,
I am using the address resolution function getaddrinfo. Everythink looks fine, however I am wondering which DNS is used for that and if it is possible to update the...
Hi,
I am trying to do a quick PoC to connect some thread nodes to the cloud through a BorderRouter(RPi3b+ running Nordic Border Router, connected to a router using LAN...
I started with the peripherals/spi example, and am now trying to update to the recommended nfrx drivers. I can get the spi working fine, but I can not get the linking to work...
I am setting some manufacturer specific data to broadcast using sd_ble_gap_adv_data_set().
The data gets sent out perfectly when the advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND...
In my application, a host co-processor controls when to start/stop advertising, connect etc.
I've noticed that soft-device command are state-dependent, e.g. calling ble_advertising_start...
Hello, I discovered strange behaviour related to reset pin on my nrf52833 prototype and SDK17. My board has only reset button connected to reset input and 10K pull-up resistor...
Hello,
I'm having an issue with a hard fault when trying to write a specific value to a peripheral chip (TDC7201) register after multiple successful writes to the same register...
Hi all,
We're starting to move to the nrf52840 platform and have a question about the adc.. We'd like about ~13 bits of effective resolution- right now we use an ads1115...
Hi, I would like to try the Alexa_Gadget sample supplied in nRF Connect SDK v1.4.0 on an nRF52382DK but the sample does not build. I have tried both SES and command line builds...
We've been asked to run BLE transmissions using Ble_LR500Kbit, that is, Long range 500kbit/s TX. 125 kbit/s and 500 kbit/s RX on the nRF52840. The transmissions would be data...
Hello,
how much effort would it take to switch an application from the nRF52832 to the nRF52840 chip?
What we want to do is, we have a running application with the nRF52832...
To the kind attention of Nordic support team,
I'm interested in implementing some sort of validation stage using a keycode, as you mention in:
https://infocenter.nordicsemi...
