When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi all,
I have tried to flash the blinky programm to the BMD 300 AR evaluation board by nRF command line tools but I can't flash the .hex file to my evaluation board. The...
I followed this tutorial :Bluetooth low energy Characteristics, a beginner's tutorial
i am beginner to study BLE.
I wanna the answer Challenge 1: Why are you not allowed...
Hello,
Our setup:
IDE : Segger Embedded Studio for ARM V4.12, nRFgo studio
SDK : nRF5_SDK_15.2.0_9412b96 + SDK for Mesh3.1.0,
Softdevice : 6.1.1
Computer Platform...
Hi, I'm using SDK12.1 example ble_app_ancs_c.
Is it possible keep advertising (non-connectable is ok) when ancs connecting?
And how to do it?
I tried call advertising_start...
Hi,
I have been having issues with the compile hex files I get when following the steps to build the pc-ble-driver (). While I am able to build the hex files when I place...
I got Orange sim connected to LTE-M network on nrf9160 DK, verified it on LTE link monitor. But when i tried adding a LTE device on nrf connect cloud, i am not able to register...
Hi,
I tried to build the lte_ble_gateway sample in SES, however it gives the error below regarding the UART.
Any suggestions how to resolve this issue?
Hi,
As mentioned in the subject, I am confused with the SPIS example from nRF52 SDK 15.3.0. I wonder where NRFX_SPIS and _INST_IDX are defined in the header file?
SPIS...
Hello,
I am testing the Light Switch example and I observed a problem:
- I noticed that it was possible to reset the "server nodes" by pressing their "button 4" to leave...
I am having an issue migrating some code over from Keil to an example in SES studio.
The code in Keil is simply listening for a radio packet, when it receives it, it transmits...
Hello,
I generate a private key by using nrfutil.
I like to convert raw data format to use in the code from private key.
Additionally, I already used a nrf_crypto_ecc_key_pair_generate...
I want to drive a servo by the PWM on nrf52832. The pwm cycle is 20ms and the duty is 1.5ms. But i have a problem that the duty is not precise when the BLE is working. I need...
Hi,
I am using a Sparkfun nRF52832 Breakout board with the Arduino IDE. My objective is to control 3 SPI digital potentiometer. The problem is I don't know how to select...
