I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi,
I am using the light switch example with the mesh SDK version 3.10
the provisioning is done with NRF Mesh application (android phone)
1. is there easy way to get...
The table under 5.4.4.3 in the datasheet for the nRF52840 lists the shunt capacitance for the LFXO as 2pF max
C0_LFXO (Shunt capacitance) 2pF max
What is the risk if the...
Well - Where shall I begin? The more I look around on the web the more confused I get.
I need to create a Connection betwen a PC running Windows 10 and a sensor device server...
Hi,
I have setup TWI peripheral for async transfers via IRQ and callback. After firing the transfer operation, I feel uneasy about having no control until the interrupt...
Hi
I need to certify a product in FCC and they sent us what they want. Radio_test_example is basically what I need, but the problem is that I'm using SoftDevice 110 and...
I was working with the buttonless DFU service that requires bonds and I was able to update my firmware just fine. Then I added Just Works OOB pairing using the nfc_ble_pair_lib...
Hello,
I am in big problem, just couple of months ago i managed to run dfu over BLE mesh. Even now its working in windows platform but for some strange reason its not working...
Hi,
I use dongles with custom application that combines Thread and CDC ACM. The application works fine, but after restarting PC several dongles with this application stopped...
Hi,
I have a smartwatch that has a nrf52832 chip inside. It firmware runs on S132 SoftDevice ver 2.0.1 and has an OTA bootloader which supposingly allows me to upload firmware...
I am evaluating the nRF5284 SDK 15 Module in HCI mode. I am trying to scan Extended advertise when: 1.Extended non connectable non scannable advertising, Primary_Advertising_PHY...
Hi,
I have just purchased a nRF52840 usb dongle ( https://www.mouser.in/ProductDetail/Nordic-Semiconductor/nRF52840-Dongle?qs=gTYE2QTfZfTbdrOaMHWEZg==) .
I would like...
Hello, I am a beginner and I just got a Raytac "MDBT50Q" bluetooth 5 module based of nRF52840 Soc.MDBT50Q does not come with a builtin frimware to respond to AT-commands.Can...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
