I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I want to use "Manufacturer Specific Data". I created a sample program, but 8 bytes from the beginning are not...
Hello,
has someone running a working example to open a TCP socket including TLS? Or what is the best base to start?
I am struggeling with the certs and key... is there...
Hi there, I have a potentially dumb or creative question that i cant seem to get a good answer on. I am running a device that is going to be conscious of uA level power consumption...
Hi,nordic team
In programming code with v2.9.0\nrf\subsys\bluetooth\conn_ctx.c
and found some bugs of mutex lock.For losing unlock result in lock forever bug.
The selected...
To preface:
nRF Connect SDK 2.9.0
nRF9151 DK
Windows 11 PC
Hello,
I just stumbled upon a potential issue after trying to figure out why I couldn't use 'softreset...
Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board.
I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code.
The board...
I build the NCS 2.9.1 connectivity bridge with
west build -b thingy91x/nrf5340/cpuapp
when I try to flash that with jlink, I get
west flash -- west flash: rebuilding...
Hi I'm trying to get more insight about nRF7002 power supply requirements. My last question didn't get a follow up so I guess a block diagram of the internal power arch was...
What would happen if a battery were connected in reverse to the nPM1100? Would it cause damage to the IC, trigger any protection mechanisms, or result in abnormal behavior...
When Developing with nRF5 SDK, follow the Developing for the nRF52805 with nRF5 SDK - Getting Started - nRF5 SDK guides - Nordic DevZone 。
The Peripheral UART Example runs...
Hi Nordic,
I have a general question about kernel threads in the mesh stack. From memory, Bluetooth has its own thread in the stack I think. At some point in the stack the...
Hi,
As title, please help to share the required information for nRF52085 pre-design evaluation, thank you.
1. Reference schematic & layout file & guidance.
2. Design...
I've installed Visual Studio Code and nrfutil and nRF Connect and J-Link and managed to compile Blinky and flash the Thingy:91 X using the terminal:
./nrfutil device program...
Dear all,
I’m working on a project using the nRF9151-DK and need to implement frequent data transmission via LTE. My setup includes multiple I2C sensors, and I want to send...
