Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, one of my nRF52840 dongles cannot be detect in device manager. When I plugged it into a USB port on my pc, the red light slowly blinks and it didn't appeared in ports...
Hello there,
I got an error msg when I tried to compile the Bluetooth LE UART service example for nRF54L15-DK as: " devicetree error: /chosen: undefined node label 'uart0...
I am using the LORA Drivers provided by zephyr for testing my SX1762 lora module with NRF52833 Development Kit. I am able to initialize and configure the LORA Peripherals...
Hi,
I am working on an FCC cert of our product which is nRF52811 based. We are currently on SDK 2.0.0. I have copied from the nrf samples bluetooth area the projects peripheral_uart...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
I am trying SPI Master/Slave communication between two nRF54L15-DK boards, using the nRF Connect SDK v2.8.0 and nRF54L15-DK 0.9.1 and 0.8.1. However, it seems that the SPIS...
Hi,
I just got my Thingy91x up and running, and it’s been on for a few hours now, but it has already used 460/500 location requests. How often does the unit send location...
Hi, I am trying to flash to a new design which uses ublox NORA-B120 module. I am trying to flash from vsc. But the flashing fails with following error.
Anyone can help...
Hello,
I have configured 2 nRF5340 boards for LE audio streaming from my mac. Two things I am noticing:
1. The audio is streaming but it is intermittent. Audio plays...
I found out nrf_reset_network_force_off() can be used to turn on/off the network core in firmware, per the example in NCS v2.5.0, samples/subsys/ipc/ipc_service/icmsg . I...
Hi,
I am making an application based on the peripheral-nus example. The checking for CR is removed and all characters are just sent further when available. The problem is...
Hi, I have developed a stable program on the nRF52840 board, and now I'm transporting all the code, and trying to make it compatible with an nRF54L15 board.
I used ZMS to...
Howdy,
I am currently working on the nRF52840 chip and trying to convert my SPIS code from being in my main while loop into being interrupt driven. I am using Zephyr to...
Hi!
I want to integrate power management into our FW. Therefor I did enable it in the prj.conf:
And added runtime enable and action run calls regarding this device...
