Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello community,
I was hoping to ask 2 questions about my design choices when designing around the nRF52840, specifically the QIAA-R branch.
First, I am confused on as...
Hi,
The Light Lightness Control (LC) Server controls a single Light Lightness Server instance on the same device with a state machine. Is there any application that demonstrate...
Hello,
I am using Bluetooth mesh for a project. I have a central device acting as a provisioner, and node devices that get provisioned as normal through this device. I am...
Hi,
My company has a product that is in production using the nRF5340 SOC. We noted this morning that the product would boot and application code even if the nRF5340's reset...
Hi there, I've a following set:
nPM1300-EK (PCA10152 / 1.3.0 / 2025.18 / Serial no. 10B3B784F5316C68)
nRF Connect v5.2.0
nPM PowerUP v2.2.3
After launching nPM...
Hello,
I’m evaluating whether simultaneous uplink from two ESB nodes is possible on the nRF54L15 DK. The documentation mentions support for up to 8 pipes in a star topology...
Hello,
I am using the ANNA-B112 module with nRF52832 to communicate to an AD5940 AFE using SPI1. I am also communicating with three other sensors using I2C0. This project...
Hi,
We enabled the DFU and sent a new application successfully using the mcumgr command line program, but now we need to do this upgrade process using the host MCU.
...
I am working through an evaluation stage for a new product using nRD52840, possibly updated to nRF54L in the next development phase. The device is based upon Zephyr and being...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Hi
I have a nRF52840 setup with external 32 kHz xtal and external 32 MHz xtal, supplied by 3.3V.
I would like the system to be in as low power mode as possible.
Each...
While testing BLE and USB individualy, they seem to work well. When there is simultaneous use, there appear frequent crashes/lock-ups in varius handlers.
BLE used: ble_app_uart...
Hi,
I've got an nRF54L15-DK, and I'm trying to get the sysbuild with mcuboot example working. https://docs.zephyrproject.org/latest/samples/sysbuild/with_mcuboot/README...
Hi,
I would like to repurpose nRFready Smart Remote 3 for nRF52 reference design to use it with the nRF54L15 DK to run BLe channel sounding experiments over this Christmas...
