Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
We have a common codebase with both softdevice (nRF51/52 code) and now zephyr (nRF54 code). To make our code compatible I have the following replacement to sd_temp_get. This...
Hello Nordic team,
We're experiencing a GNSS issue with our nRF9160-DK (PCA10090 1.1.3 2024.44) and would appreciate any guidance you can provide. About 4 days ago, we were...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
ncs v2.6.1
If I use bt_conn_le_create() and do not use the default (0) value for create_param->timeout, the actual connection creation timeout does not match the description...
I'm trying to program a custom board with a Raytac nRF52832 module using the nRF52 DK's onboard J-Link via the P20 debug out port. The J-Link only detects the onboard nRF52832...
Hi,
I've been working through the Nordic Bluetooth ESL Tutorial and have the sample code up and running (using a nRF52833 DK as the tag and a nRF5340 DK as the access point...
We have custom hadware which we can successfully added the bootloader. We can generate .bin files & bootload them via BLE using the Nordic devicemanger app on our smart phone...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
What is the permitted VDD ripple on the nRF9151?
I see " To minimize supply voltage ripple and suppress EMI coupling to and from nRF9151 VDD , keep supply network impedance...
