Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi there! Our app developer are experiencing some difficulties with Bluetooth LE and image/file transfer on iOS. The device (our product) uses the NRF52840 chip. Any help...
Hello,
Using nRFConnect 2.1.0
I am trying to build the peripheral_iso zephyr sample, for the nRF52840 DK
It compiles fine as is (with the original board qemu_cortex_m3...
For some reason my ticket got deleted earlier, so here I go again.
I'm trying to change the configuration of the network core bootloader. For the `hci_rpmsg` and `mcuboot...
Hello,
I am going through the tutorials in the DevAcademy. During the learning process, I noticed the nRF Connect SDK is updated several times. I started from 2.1.0, now...
I am trying to make a multiprotocol network using BLE and Thread. I have flashed nRF52840DK using the `s140` Softdevice and flashed the ble_thread_dyn_template as well.
...
Hi,
I am currently using the NRF52840 DK to evaluate the NFC functionalities of the SoC. It works very well with a smartphone.
I'd like to understand the NFC on the NRF52840...
Hi,
We are developing a matter curtain product the power by battery.I setup SED mode for low power. The larger the POLL PERIOD value I set , the worse the real-time performance...
Dear Support team
I don't quite understand the part as the picture below after I read the specification, I would like to kown What are the output drive modes in the picture...
I want to make an NFC card with Ntag 213, which is an NFC Type 2 tag.The card needs to write data to a specific block via NFC.
However, the NFC Type 2 tag library does not...
Hi, as stated at page 15 in the Direction Finding white paper(nWP-036), it says 'When the last switch pattern is reached and IQ sampling continues, the switch pattern loops...
//nRF52840 DK//PCA10056//central=apple-smartphone//Wireshark Version 4.0.1 (v4.0.1-0-ge9f3970b1527) sniffer.//
Wireshark is working perfectly on Advertising packets, but...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
Is the nRF9160 capable of operating on the CBRS band (b48)?
I know it is not listed as a band that is supported by HW but I am curious if there is a software workaround...
Hi Nordic Team,
I am working on the BIS demo, I have three nRF5340 DK audio boards, so I set one as Source, two others as Sink, so is there any resources that when Source...
Hi,
After lots of issues with build and deploy, I eventually have a working version of a BLE App running on a XM122 Radar module. This module have to be packeaged with the...
